Skip to main content
Redmoon Converters
🖥️

By ·

Choosing a Gaming Monitor by the Numbers: Hz, Pixels and the Cable in Between

What each refresh-rate step buys in milliseconds, whether your GPU can feed it at 1440p, ultrawide or 4K, and the DisplayPort and HDMI data rates that decide whether you get full refresh at all.

GamingElectronics

Monitor listings lead with two numbers, refresh rate and resolution, as if each were an upgrade you just buy. In practice they compete for the same graphics card, and a third number the listing barely mentions, the data rate of the port and cable, decides whether you get either of them at full strength. A 4K 240 Hz panel on a card that renders 70 fps at 4K, connected over a link that can’t carry 240 Hz uncompressed, is a 70 Hz monitor that cost a lot of money.

This guide puts numbers on the three limits. FPS to frame time covers why frame time is the honest unit and how it relates to input lag, so we’ll start from there.

What each Hz step actually buys

Frame time is 1000 ÷ Hz, so equal steps in Hz give smaller and smaller steps in milliseconds. A more useful way to compare the refresh rates monitors are actually sold at is to ask how much time each extra hertz saves at that point on the curve:

UpgradeFrame timeSaved per frameSaved per extra Hz
60 → 100 Hz16.67 → 10.00 ms6.67 ms167 µs
100 → 144 Hz10.00 → 6.94 ms3.06 ms69 µs
144 → 165 Hz6.94 → 6.06 ms0.88 ms42 µs
165 → 180 Hz6.06 → 5.56 ms0.51 ms34 µs
180 → 240 Hz5.56 → 4.17 ms1.39 ms23 µs
240 → 280 Hz4.17 → 3.57 ms0.60 ms15 µs
280 → 360 Hz3.57 → 2.78 ms0.79 ms10 µs
360 → 500 Hz2.78 → 2.00 ms0.78 ms6 µs

The last column shows what the marketing hides. A hertz at the bottom of the range is worth about thirty times as much as a hertz at the top. Going from 60 to 100 Hz saves more per frame than every step from 144 to 500 combined (6.67 ms against 4.94 ms in total).

That doesn’t make high refresh pointless. It means you should know what each step costs. Put 144 and 165 into the FPS to Frame Time Calculator and it reports “0.88 ms saves”. That’s worth having when 165 Hz costs the same as 144, which it often does now. It isn’t worth paying much extra for. The calculator’s reference table covers 24 through 480 FPS, and its two input boxes take any value up to 1,000, so 180, 280 and 500 can be entered by hand.

A refresh rate is only real if your GPU can fill it

A 240 Hz monitor shows a new image every 4.17 ms only if the game delivers one that often. If your card averages 110 fps, the screen gets 110 new frames a second whatever its refresh rate. Variable refresh (G-Sync, FreeSync) makes 110 fps look smooth, but the frame rate is still 110.

So turn the question around: what frame rate does your card manage at the resolution you’re considering, in the games you play? As a first approximation, when a game is GPU-bound its frame time grows with the number of pixels rendered. That scaling is never quite linear, because some of each frame’s work (geometry, CPU-side simulation) doesn’t depend on resolution. Treat it as the pessimistic edge of a range:

ResolutionMegapixelsvs 1440p
1920 × 10802.070.56×
2560 × 14403.691.00×
3440 × 14404.951.34×
3840 × 21608.292.25×

Say your card runs a game at 110 fps at 2560 × 1440 (9.09 ms per frame). At 3440 × 1440 the worst case is 9.09 × 1.34 ≈ 12.2 ms, or about 82 fps. In practice it lands somewhere between 82 and 110. At 4K the worst case is 9.09 × 2.25 ≈ 20.5 ms, which is 49 fps. A 175 Hz ultrawide on that card runs at roughly half its refresh rate, and a 4K 240 Hz panel at about a fifth.

None of the tools here does this scaling for you. It’s the arithmetic above, plus benchmarks of your own card in your own games. Use the FPS calculator in the other direction: turn a benchmark result into milliseconds and compare it with the panel’s frame budget (6.06 ms at 165 Hz, 4.17 ms at 240 Hz). If the budget is much smaller than your frame time, the extra refresh will go unused. Upscalers like DLSS and FSR shift this calculation by rendering fewer pixels internally. Esports titles at 1080p, often limited by the CPU rather than the GPU, are where 360 Hz and above can actually be fed.

Ultrawide isn’t exactly 21:9, and that affects more than the box

“21:9” is a marketing label for several slightly different shapes. Switch the Aspect Ratio Resizer to its ratio mode and enter the real panel resolutions:

PanelSimplest ratioDecimal
2560 × 108064:272.370
3440 × 144043:182.389
3840 × 160012:52.400
5120 × 144032:93.556

True 21:9 would be 2.333. Click the resizer’s 21:9 preset with a width of 3440 and it gives a height of 1474, not 1440. This matters in two places. Video mastered for cinema’s 2.39:1 fills a 3440 × 1440 panel almost exactly, while 16:9 content gets black bars at the sides. And games that widen the field of view for wider screens (most modern ones) show more of the scene at the edges, while some competitive titles stretch, crop or pillarbox instead. Check how your main game handles 43:18 before you commit.

Your aim carries over unchanged. cm/360 depends on DPI, in-game sensitivity and the game’s yaw, not on resolution or refresh rate. That’s why the Mouse Sensitivity Converter has no resolution field. A wider field of view does change how fast the centre of the screen seems to move at the same cm/360. The sensitivity conversion guide covers that FOV caveat. Give it a few sessions before you touch the setting.

The cable: data rate decides what you actually get

A monitor’s spec sheet can list 240 Hz while the port you plug into can’t carry 240 Hz at that resolution. Uncompressed video needs roughly:

data rate ≈ width × height × refresh × bits per pixel

Bits per pixel is 24 for 8-bit colour and 30 for 10-bit (three channels each). On top of that, a real video signal includes blanking intervals, which add roughly 5–15% under standard reduced-blanking timings and more at very high refresh rates. These are approximate figures. Exact timings vary by monitor.

The links have fixed ceilings. The number on the box is the raw signalling rate. What’s left for pixels after line encoding is lower:

LinkRaw rateUsable for video
HDMI 2.018 Gbps≈14.4 Gbps
DisplayPort 1.4 (HBR3)32.4 Gbps≈25.9 Gbps
HDMI 2.1 (48G FRL)48 Gbps≈42.6 Gbps
DisplayPort 2.1 UHBR13.554 Gbps≈52 Gbps
DisplayPort 2.1 UHBR2080 Gbps≈77 Gbps

Now compare common modes. The figures include standard blanking and are rounded:

Mode8-bit10-bitWhat carries it uncompressed
2560 × 1440 @ 144~14 Gbps~18 Gbps8-bit just fits HDMI 2.0; DP 1.4 handles both
2560 × 1440 @ 165~16 Gbps~20 GbpsToo much for HDMI 2.0; fine on DP 1.4
3440 × 1440 @ 175~23 Gbps~29 GbpsDP 1.4 at 8-bit only; 10-bit needs more
3840 × 2160 @ 144~31 Gbps~39 GbpsOver DP 1.4 even at 8-bit; fits HDMI 2.1
3840 × 2160 @ 240~55 Gbps~69 GbpsOnly DP 2.1 UHBR20

This is why some 175 Hz ultrawides drop to 8-bit colour at their top refresh rate, and why a 1440p 165 Hz monitor on an older HDMI 2.0 port stops at 144.

The way past these ceilings is Display Stream Compression (DSC). It’s a visually lossless compression scheme supported on DisplayPort 1.4 and HDMI 2.1, and it’s how most 4K high-refresh monitors reach their rated refresh over DP 1.4. It works well, but both the graphics card and the monitor have to support it, and some GPUs restrict other features (certain multi-display setups or driver-level supersampling, for example) while it’s active.

Before you buy, check three things:

  • The port’s real rate, not its version number. HDMI 2.1 is a feature set, and a port labelled 2.1 can run at well below 48 Gbps. The monitor’s manual should state the maximum refresh per input.
  • Your graphics card’s outputs. Many cards still in use have DP 1.4 ports, which makes a UHBR20 monitor a DP 1.4 monitor in practice.
  • The cable’s certification. For HDMI 2.1 speeds look for “Ultra High Speed HDMI”, and for DP 2.1 look for DP40 (UHBR10) or DP80 (UHBR20). An old cable can quietly force the link down to a lower rate.

Do the sums before you choose the panel

Choose the refresh rate whose extra milliseconds are worth the money to you, check that your GPU can actually render that many frames at that resolution, and make sure the port and cable can carry the result. The FPS to Frame Time Calculator handles the millisecond comparisons. The Aspect Ratio Resizer tells you what shape a panel really is, and the Mouse Sensitivity Converter confirms your cm/360 won’t need to change.

Try the tools from this guide